Toyota Troopy 'Rear Pull out ' Pop Top Awning Brackets
This Set of Brackets is Built specifically for Straight out rear deployed Pull out awnings - Typically these are 1350mm long and run poles when deployed. The Brackets are strong enough to handle rear deployable double sided 180 awnings also, but we'd not reccomend them as the space is largely unusable. (Stick to the 270's)
See Other Listings for Other awning types.
General information about the bracket set
The Troopie "Pole Less Awning to Vehicle" Kit ultilises a twin Bolting clamp design - 1 Set each side for ultimate strength
The Rear bracket triangulates around the rear of the truck - on both sides providing Ultimate anti twist strength - for a super ridgid Pull out rear awning set up.
If you are Installing this Gutter Bracket, Please ensure that your Gutters are free of dirt, Putty, glue, fibreglass or any obstructions. If it isnt - make it free from Gunk by scraping it out with a blade or similar. From there the Gutter mount kit simply Drops into the gutter, clamps are then bolted on from the outside edge and your brackets are installed.
Installation video on You tube here - (Its filmed in Real Time - Installation was under 10 minutes)
THIS KIT DOES NOT INCLUDE THE HOOK BRACKET NOR THE FRONT FOOT STAND - IT ONLY WORKS WITH REAR PULL OUT AWNINGS
All Kits Come PRe-Assembled ready to fit.
SHIPPING - Delivery Times
The Gutter Mount troopie Brackets (Awning to Vehicle ) brackets are made to order here in Melbourne. They have a lot of components and we rely on 4 different engineering companies locally for their manufacture / Fabrication and Finish. We tend to make a couple of dozen sets every month - Delivery times can vary up to a week to a month depending on current stock levels and availability of components..
More General info on shipping rates can be found here.
More information on Varients and or Our Release of 'VERSIONS' and Product Warranty can be found here https://www.toughtouring.com.au/about-1
Parts LIST
Kit Includes:
6 x Gutter Clamps
4 pieces of Rear Brackets (Made up of 2 Bolt Together components each side)
Tough Touring Logo in 3mm Aluminium and 2 Rivetts ( 1 Logo Each side) .Installation
You will need a 6mm Allen Key to complete this installation. Moving of aftermarket Latches etc (Added by Pop top intsallers) may be required -
Installation Video of how to bolt up and install the brackets here - https://youtu.be/5mPIzo1clbU?si=qCy61au-P-K9lD0i
The Tough Touring Awning to Pop top Troopy brackets accept all know Rear Pull out awnings
Basic Tech Specs and Tools required
All Brackets finished in Black Dulux Textura Powdercoat , Baked at 500 Degrees Celcuis... They are Made in Australia right here in Melbourne and assembled by the Team at Tough Touring pretty much by hand...
The Bracket set comes complete with all mounting hardware and a tube of White Sikka Flex as to facilitate a dot to adhere the front supporting leg to the vehicle to prevent rattle. Awning mounting bolts are not supplied, as these should come with your awning...
You will need a 13mm Spanner, 6mm Allen Key and thats about it to effictively install the kit to your vehicle.
The Front support bracket should be mounted loose firstly, then propped in a vertical position overnight while the dab of Sikka Cures. Then Install the Awning .
Video here of a worst case troopcarrier with Resin filling the gutters as well as bolt rope track fitted in the way, Pop top roof latches in the way and inproperly secured pop top - all fixed in the video with basic tools... We've never seen one this bad since - but it still came up fantastic with a bit of sanding and TLC.
Care should be taken to guy down and even Run poles on Pole less wing awnings in unprectable wind to ensure no damage is occassioned to your awning or vehicle should wind strength exceed the awnings load limits.