top of page
Toyota 100 and 105  Series Roof Top Tent Rack

Toyota 100 and 105 Series Roof Top Tent Rack

$1,490.00Price
GST Included

Tough Touring 100 Series Toyota  RoofTop Tent rack is a Low Profile / outward folded roof rack designed Specifically for roof top tents and  heavy loads consistent with offroad touring. 

 

Awnings can be Mounted directly to the rack - beside the tent using our Awning to Rack kit - Listed here https://www.toughtouring.com.au/product-page/awning-to-tough-touring-rack-bracket-up-or-down-mount

 

Our custom designed rails and  Aluminium Top hat crossbars  form a super strong, low foundation for your chosen roof top tent and Awning Combination. Capable of handling typical Hardshell Tent loads on Off road environments -

 

The Tough Touring Racks are so low they help wind drag and noise from bulky Tents, while the low profile and forward positioning that the rack provides moves the  weight of the touring gear lower and futher forward than traditional touring racks - which also help reduce body roll /improving vehicle stability. 

 

The LC 100 Once Piece Rack we supply has been designed with ' shorter  rear' , allowing pole less wing awnings to swing through their arc and be set up with minimal fouling on the rear doors Wind fairing.  This also allow RTT to sit lower and not foul on the large accessories Aerial mounted on the 100.

The roof top tent option of this rack allows  "independent awning to tent fittment" For tents that cannot handle fitment of awnings directly to the tent...

 

We also manufacture Awning to Tent Brackets for the vast majority of roof top tents. See more on these here - https://www.toughtouring.com.au/tent-to-awning-brackets

 

If you have to install the awning directly to the roof top tent rack, ensure that you order planks around 50-75mm Wider than your tent.... You will need a 4th back plank to do the job nice...We call this type of roof top tent installation "Independent awning to Tent Install" - Its common to have to do it this way  If your Going to run a low sidewalll Roof top tent - or a plastic tent / weak sides, no slots etc and cannot ensure tent stiffness for  'AWNING TO TENT' install - see the information page here on options to install your Pole less wing awning directly to the rack (Independently to the tent) - https://www.toughtouring.com.au/tent-to-vehicle-kits More on this below here. .

 

The awning bracket kit for suitable Roof top tents that are going to run the awning seperatly on the rack is listed here - 

 

https://www.toughtouring.com.au/product-page/awning-to-tough-touring-rack-bracket-up-or-down-mount

 

0/500
Quantity
  • Specifications and Installation

    SPECIFICATION

    At Present - we have moved to General Release Version  of this rack - Its design has evolved into a 1 piece foot rail and with 4 seperate feet - Improvements have further increased strength and its simple installation makes it a no brainer.

    INSTALLATION 

    Tips on Installation are here online in Video format - https://youtu.be/PlXv-3uHB30... 

    (no printed instructions come with the rack) 

    RECCOMMENDED PLANK WIDTHS

    For Ultimate strength and easy install / removal the standard size is 1400mm bar planks to go with this rack for all roof top tents  - Except the Bundutop KING which requires  1550mm planks .

    If your Going to install your awning to the rack rather than the tent, We'd reccommend you order at least  50mm wider Top hat bar planks than your tent width.

    All Planks supplied are now manufactured in Aluminium for lighter weight and Corrossion resistance. 

    Top Outfold Foot rails are folded outwards at 80 Degrees, while the rack feet are our standard 75 Degree fold.  (InFold is a Plus 100 Fold) 

    Our custom designed rails and crossbars form a super strong, low foundation for your chosen roof top tent and Awning Combination. Capable of handling typical Hardshell Tent loads on Off road environments - The Tough Touring Racks are so low they help reduce wind noise while getting the weight of the touring gear lower -

    minimising vehicle body roll.

    ABOUT THE RACK - THE EXTRAS

    The One piece rack we supply we've kept it short at the rear, allowing pole less wing awnings to swing through their arc and be set up over the space above the rear door, stopping rain ingress,, Its also important to keep roof weight forward as it improves vehicle handling etc as well...

    Please note that if your wishing to accessing a roof top tent from the rear on the 100 series, YOU CANNOT USE THE STANDARD LADDER HERE, as the Wind fairing fouls on the tent unless you fit it RIGHT back at the rear which will cause other issues...

    We'd reccommend you fit an aftermarket  rear door ladders (One that is fixed to the vehicle) .. on this vehicle is Our rack design takes into account this option, as fitting the tent forward offers more of the the pro's and less of the cons 

    Alternatively The 100 series has no issues with ladder access from the drivers side of the vehicle. 

    INCLUSION LIST

    The LC 100,105 Tough Touring Roof rack Kits includes:

    * 2 x Super Low One Piece outward folded 3mm Mild Steel / 8 point roof rails (80Degrees outward Fold) - 1950mm long

    * 3 x TOP HAT BAR  Planks / Slats - 1400mm in Aluminium Powdercoated BLACK

    * 8 x 75 Degree Folded Roof rail Feet

    * Assorted ABS  spacers

    * 16 x High Tensile Hex Bolts and washers for rail mounting into the rail channels

    1 Tube Sikka flex Adhesive sealant

    16 x 20mm Countersunk Hex Head bolts and Nyloc nuts for fastening roof planks to rails.

    *Unique Design means all bolts to roof rack planks are accessable from beside the vehicle for easy removal once fitted.

    Made to order - As these racks are still moving through minor dev changes - we only cut them 3 at a time. Your order will usually be delivered within around 4 weeks (SOmetimes shorter) depending on where the present cut / powdercoating stock is at.. Its all local manufactured - so we will give you an update when order is placed.

     

  • Tech Specs

    The top rail feet have been heat folded to 75 Degree angles to allow maximum camber while still giveing tool access, top foot rails now folded through 100 degrees - (outfolded)  (1 big lengthways fold) for super solid - zero flex -and heavy load...  Unreal rack.. The 100 is among our favorite vehicles and its 4 point super strong roof just makes it easy for us to look good :) 

    Recent updates means the Kit now comes complete with 8  x ABS Plastic 10mm spacers - allowing fittment of the rack kit without removal of the Roofs rubber inset trim.. (The feet fit straight in Easy as). 

     

    All parts made in Australia using Mild Steel, Sandblasted and Powdercoated in Black Dulux Textura. 

No Reviews YetShare your thoughts. Be the first to leave a review.
bottom of page