These brackets provide twin 3mm plate steel ridgid Awning Mounts,  They are strong enough to handle all known heavy duty  of Pole less awnings. 
This brackets set is manufactured in Australia - they features additional stiffening triangles on the bottom edge - the bracket is folded to negate the need for spacers, pushing  the awning out  approx  20mm out  from the edge of the bundutop tent.
 
The Awning comes in a MID mount or an UP mount. THIS LISTING IS FOR THE UP MOUNT ... Mid mount places the awning pretty much flush with the tents base, while the up mount adds an additional 50-80mm of height dependent on the awning fixing mounts... 
 
The Mounting points facilitate Awning mounts right down to 1940mm spacing, with a wider option also for longer awings. The 'INFOLD' set up of these brackets brings the rear arm in as close as possible to the rear of the tent - preventing rain getting through any large gaps. 

We have also now an integrated Adjustable hook bracket which is included  in this kit, allowing adjustment of awning tension on the fly using a 13mm Spanner and 6mm Hex Allen key.  We do not include the hook bracket with Customers owning The Bush company Awnings - as they have the canvas rolled under the last arm and cannot use our hook bracket. 
 
If you need it - THe Kit also can be optioned below to include our 'Bundu Suite' Integration kit, which adds a 4th corner steel plate on the front drivers side, allowing the Bundutop SUITE to be mounted over the Tents Buttons, hinging the suite and allowing the ladder mount to remain on the Drivers side of the vehicle. 
 
If your intending to install a 360 Awning -  Please check your awnings mounting spec - (Length ) and ensure that the arms when set up will still cup the Bundutop tent ok...(The tents  are 2.1m Long (  We don't know the entire range of awings geometry worldwide.. Its too many - so we have built the brackets as a standard kit to work for all awnings....  An Ostrich wing for example when mounted - will have the rear arm set 100mm behind the point where its bolted - with this bracket set the  awning arm ends up about 30mm behind the tent when open, so does the bush company awnings , but ..  others will be different, and the swing out measurement should be stated on their spec sheets. 
 
If the rear bracket is 'Inset' - this takes the mounting position of the awning forward 50mm - so in the example above - an ostrich wing would then have its rear arm just 50mm behind the tent.
 
The Kit comes complete with 
 - Sealed Rivetts and Videos are provided on our you tube channel to assist home builders and pro fitters alike.
SUPPORTED AWNINGS PLEASE READ:
 
The Kit  supports all known Pole Less awning types  : (Quick Pitch, , Alucab 270,  Howling moon 270 and 270 forward fold 180, Bundutec 360, Bundutec 270 and Bundutec 'L' Bushwakka 270 Extreme Darkness, Bush wakka 180 Extreme Next Gen  (1950 back plate)  , Eezi Awn Manta 270,  Darche 180 double end  and single end, Darche 270, 30 second awning, BushWakka 180/270 and forward fold 180/270, and BOSS 270 (BA 270 Awnings)
The Bush Company XT Max, XT 270, XT 180 and XT 180 Double End -are also now supported.
 
These Brackets have fixed mounting points at 1940m apart. 
 
 
NOTES ON THE SUPPORTED AWNINGS / Bolt patterns. 

ALUCAB and HOWLING MOON
This Kit now  supports Alucab , Howling Moon , Bushwakka and quick pitch  awnings  (These awning run a 4 bolt x 50mm pattern and the Awning brackets supplied are now cut into this pattern to suit) 
 
 
BUNDUTOP TENT NOTES: 
The Bundutop Tent is shorter than most at just 2.1m long, and its large flat faces make it ideal for fitment of awnings - The Bundutop tent is Capable of taking Double ended Bush company XT 180 Awnings - as well as the XT max - However we do reccommend carrying poles and Guy ropes in even mid strength wind - as these awnings do not 'wrap around the tent' and thus exert all twist pressure on just the one side of the tents they are fitted too..